RS 909
0. Wheel data (short version)
|
wheel type |
Wheel size / offset |
Allowable. Wheel load / max. Rolling circumference |
Zentrierart |
Wheel mounting |
|
RS 909 |
8 1/2 J x 18 H2 ET 38 |
765 kg / 1940 mm |
mid centering |
conebund screw M12 x 1.5 x 29 |
NOTE: Subsequent mechanical machining and / or thermal treatment is not permitted. Such a wheel no longer corresponds to the tested revision and when mounted on a vehicle invalidate the operating on public roads.
1.Range of
Vehicle Manufacturer: Bayerische Motoren Werke AG. Munich
|
Type |
Approval - No. 1) |
Embodiment (engine type) |
trade name |
|
187 |
e1 * xx / xx * 0287 *. , |
UF1. (N45B16A) |
BMW 116i (85 kW) |
|
UF3. (N46B20B) |
BMW 118i (95 kW) |
||
|
UF5. (N46B20B) |
BMW 120i (110 kW) |
||
|
UF9. (N52B30A) |
BMW 130i (195 kW) |
||
|
UG3. (204D4) |
BMW 118d (89 or 90 kW) |
||
|
UG5. (204D4) |
BMW 120d (110 or 120 kW) |
1) xx / xx documents the current state of the Directive 70/156 / EEC (Total approval)
and _ the respective addendum to the operating permit. The assignment of the vehicle type to
Approval is sufficient for the needs of this expert opinion.
2. Tires
In conjunction with the wheel-type RS 909 following tires combinations in consideration of the respective conditions and notes are valid:
|
combination 1: requirements and |
||
|
front |
225/40 R 18 - XX * |
R) 10) 13) 35) |
|
behind |
225/40 R 18 - XX * |
R) 11) 12) 14) 35) |
|
Combination 2: |
||
|
front |
225/40 R 18 - XX * |
R) 10) 13) 35) |
|
behind |
245/35 R 18 - XX * |
R) 11) 12) 14) 35) |
|
Combination 2: |
||
|
front |
225/40 R 18 - XX * |
R) 10) 13) 35) |
|
behind |
255/35 R 18 - XX * |
R) 11) 12) 14) 15) 35) |
3. Conditions and notes
R) are front and rear tires only one manufacturer and type allowed.
*) The required speed / load index can be found in the vehicle papers.
The suitability of the tire used, in particular the required tire pressure in conjunction with the existing load index at the respective maximum speed, the maximum axle loads and camber values and using different tire sizes in front and behind also to facilitate use in connection with electronic control systems (ABS, ASR etc.), is through the Reifenherstellernachzuweisen. Gives way to the tire from the standard pressure off the driver to point appropriately to it (air pressure sticker, complete the manual)!
10a) The wheel cover front to be produced by reworking or attachment of additional parts, which do not limit the tire clearance. Depending on the tolerance position and setup status of the cover in exceptional cases may be sufficient.
11. The rear fender is to be made. Depending on the tolerance position and setup status of the cover may be sufficient.
11a) The rear fender to be manufactured by rework or attachment of additional parts, which do not limit the tire clearance. Depending on the tolerance position and setup status of the cover in exceptional cases may be sufficient.
12. To produce sufficient Radfreigangs the rear bumper is reworked. Depending on the setup state of the vehicle (z. B. Lowering vehicle, wheel arch, etc.) it may be possible that the Radfreigang is sufficient.
13. To produce sufficient Radfreigangs the wheel arch is the front rework. Depending on the setup state of the vehicle (z. B. Lowering vehicle, wheel arch, etc.) it may be possible that the Radfreigang is sufficient.
14. To produce sufficient Radfreigangs the wheel arch is reworked rear. Depending on the setup state of the vehicle (z. B. Lowering vehicle, wheel arch, etc.) it may be possible that the Radfreigang is sufficient.
15. For producing sufficient Radfreigangs the wheel house is reworked back to the outside. Depending on the setup state of the vehicle (z. B. Lowering vehicle, wheel arch, etc.) it may be possible that the Radfreigang is sufficient.
35) The use of snow chains is not allowed.