
BBS RS-GT series
RS 909
- Size8.5x18"
- PCD5x120
- OffsetET38
RS 909 is a part number from the BBS RS-GT family of wheels. It is an 18-inch wheel, 8.5 inches wide and is listed for BMW, Audi. Vw.
The 5x120 bolt pattern of the RS 909 is the one used by BMW and some Land Rover and Honda.
ET38 is a high offset for the RS 909, so it tucks well inside the arch, as front-drive and most modern cars need. An 8.5-inch rim normally takes tyres from about 215 to 265 mm wide.
Before fitting an 18-inch RS 909, check caliper clearance as well as offset, especially on cars with larger aftermarket brakes.
No centre bore figure is recorded for the RS 909. Read the markings on the back of the wheel before relying on it.
For the history behind the RS 909, how to spot a genuine wheel and what to check when buying used, see the BBS RS-GT series guide.
Specifications
| Model / part | PCD | Diameter (in) | Width (in) | Offset (ET) | Centre bore (mm) | Lip | Barrel | Fitment | Notes |
|---|---|---|---|---|---|---|---|---|---|
| RS 909 | 5x120 | 18 | 8.5 | 38 | — | — | — | BMW, Audi. Vw | — |
Technical information
0. Wheel data (short version)
|
wheel type |
Wheel size / offset |
Max. wheel load / max. rolling circumference |
Centring type |
Wheel mounting |
|
RS 909 |
8 1/2 J x 18 H2 ET 38 |
765 kg / 1940 mm |
centre-bore centring |
Tapered-seat wheel bolt M12 x 1.5 x 29 |
NOTE: Subsequent mechanical machining and / or thermal treatment is not permitted. Such a wheel no longer corresponds to the tested revision and when mounted on a vehicle invalidate the operating on public roads.
1.Range of
Vehicle Manufacturer: Bayerische Motoren Werke AG. Munich
|
Type |
Approval - No. 1) |
Embodiment (engine type) |
trade name |
|
187 |
e1 * xx / xx * 0287 *. , |
UF1. (N45B16A) |
BMW 116i (85 kW) |
|
UF3. (N46B20B) |
BMW 118i (95 kW) |
||
|
UF5. (N46B20B) |
BMW 120i (110 kW) |
||
|
UF9. (N52B30A) |
BMW 130i (195 kW) |
||
|
UG3. (204D4) |
BMW 118d (89 or 90 kW) |
||
|
UG5. (204D4) |
BMW 120d (110 or 120 kW) |
1) xx / xx documents the current state of the Directive 70/156 / EEC (Total approval)
and _ the respective addendum to the operating permit. The assignment of the vehicle type to
Approval is sufficient for the needs of this expert opinion.
2. Tires
In conjunction with the wheel-type RS 909 following tires combinations in consideration of the respective conditions and notes are valid:
|
combination 1: requirements and |
||
|
front |
225/40 R18 |
Conditions 10, 13, 35 |
|
behind |
225/40 R18 |
Conditions 11, 12, 14, 35 |
|
Combination 2: |
||
|
front |
225/40 R18 |
Conditions 10, 13, 35 |
|
behind |
245/35 R18 |
Conditions 11, 12, 14, 35 |
|
Combination 2: |
||
|
front |
225/40 R18 |
Conditions 10, 13, 35 |
|
behind |
255/35 R18 |
Conditions 11, 12, 14, 15, 35 |
3. Conditions and notes
R) are front and rear tires only one manufacturer and type allowed.
*) The required speed / load index can be found in the vehicle papers.
The suitability of the tire used, in particular the required tire pressure in conjunction with the existing load index at the respective maximum speed, the maximum axle loads and camber values and using different tire sizes in front and behind also to facilitate use in connection with electronic control systems (ABS, ASR etc.), is through the Reifenherstellernachzuweisen. Gives way to the tire from the standard pressure off the driver to point appropriately to it (air pressure sticker, complete the manual)!
10a) The wheel cover front to be produced by reworking or attachment of additional parts, which do not limit the tire clearance. Depending on the tolerance position and setup status of the cover in exceptional cases may be sufficient.
11. The rear fender is to be made. Depending on the tolerance position and setup status of the cover may be sufficient.
11a) The rear fender to be manufactured by rework or attachment of additional parts, which do not limit the tire clearance. Depending on the tolerance position and setup status of the cover in exceptional cases may be sufficient.
12. To produce sufficient Radfreigangs the rear bumper is reworked. Depending on the setup state of the vehicle (z. B. Lowering vehicle, wheel arch, etc.) it may be possible that the Radfreigang is sufficient.
13. To produce sufficient Radfreigangs the wheel arch is the front rework. Depending on the setup state of the vehicle (z. B. Lowering vehicle, wheel arch, etc.) it may be possible that the Radfreigang is sufficient.
14. To produce sufficient Radfreigangs the wheel arch is reworked rear. Depending on the setup state of the vehicle (z. B. Lowering vehicle, wheel arch, etc.) it may be possible that the Radfreigang is sufficient.
15. For producing sufficient Radfreigangs the wheel house is reworked back to the outside. Depending on the setup state of the vehicle (z. B. Lowering vehicle, wheel arch, etc.) it may be possible that the Radfreigang is sufficient.
35) The use of snow chains is not allowed.
Size in inches, offset and bore in mm. How to read these figures.
Before you buy or fit