
BBS RS-GT series
RS 911
This page covers the RS 911, one wheel from the BBS RS-GT series.
Before fitting a RS 911, check caliper clearance as well as offset, since the barrel shape decides how much room there is for the brakes.
No centre bore or fitment or PCD or offset figure is recorded for the RS 911. Read the markings on the back of the wheel before relying on it.
More on where the RS 911 came from and how it is built is on the BBS RS-GT page.
Specifications
No measurements are on record for this part number.
Technical information
continued to
Second tires In conjunction with the wheel types RS 911 (. Exemplary 09.31.150), the following combinations are permitted different tires, taking into account the relevant conditions and notes: Combination 1:
Conditions and notes
* ) The required speed index is given in the vehicle papers. The suitability of the tire used, in particular the required Tire inflation pressure in connection with the present load index at the respective maximum speed, the maximum axle loads and camber values and using different tire sizes in front and behind also to facilitate use in connection with electronic control systems (ABS, ASR etcIs.) evidenced by the tire manufacturer. Gives way to the tire from the standard pressure off the driver to point appropriately to it (air pressure sticker, complete the manual)! In any case, corresponding Eignungsnachweise are required which can lead to further action on the vehicle and / or other conditions, if necessary, or may shown that the use must be excluded. Of the Vehicle owner / guide must ensure that when regeneration of the tire to another as the tested brand or type, it no risk or irregularity must come.
RT) In this combination, in particular the carrying capacity of the mounted on the rear axle to observe the tire.
The projecting into the wheel cutout rear bumper face is to be reduced in the upper region for a length of about 30 mm by about 5 mm from the inside (or rear apron exhibit laterally. 6c) The wheelhouse liner is reworked or on the Radhausaußenseite in the area above the rear bumper to the rear to cut. The wheelhouse liner is reworked or on the Radhausaußenseite the area above the wheel arch up to cut. On sufficient attachment to look for. 6d) The standard part folded over fold on wheel cut is at least from the rear bumper to. 260 mm in front of the wheel center Completely convert cart (tightly). Thereafter the seam is at least up to the height of the lateral bar to. Convert Cart 45 °.additionally is the wheel cutout on the rear apron by approximately 12 - 14 mm expand outwardly - auslaufend to about 130 mm from the wheel center.
12b) After carrying out the finishing work of the clearance between the tire outer side, andentire wheel cutout or Radhausaußenseite in each case with complete the inset check rear axle and possibly produce by other measures.
* * * * * * * Accreditation under DAR registration number KBA-P 00001-95 of the accreditation body of the Federal Motor Vehicle Office, Federal Republic of Germany - 4 -
Decrease of cultivation The proper state of the vehicle is ended by an officially recognized knowledgeable, or tester for motor vehicle traffic or a motor vehicle expert or an employee to a section 7.4 of Appendix VIII to traffic regulations stating
The plant BMW5 (pages 1 to 4) is only valid in connection with the report no. 18 10 08 1 181 for the wheel type RS 911th |
|
0th |
Wheel data (short version) |
|||||||
|
0.1. |
Front and rear axles |
|||||||
|
Wheel type / |
Wheel size / |
Centring type |
wheel |
|||||
|
design |
Allowable offset. wheelMaxload.Rolling/ circumference |
mounting |
||||||
|
RS 911 / |
J 8 1/2 x 18 H2 |
765 kg / |
centering |
|||||
|
09.31.150 |
ET 15 |
2098 mm |
09.23.491 cone |
bund screwM12 x 1.5 x 29 |
|
Fahrzeugh creator: |
Bay erische Motor Werke AG (BMW) Munich |
|||||||||||
|
Vehicle- |
EEC - approval |
versions |
trade name |
|||||||||
|
Type |
number. 1) |
|||||||||||
|
5 / D |
e1 * xx / xx * 0028 * .. DD |
11 / DD 12 / DD 21 / DD 22 |
||||||||||
|
11 DM / DM 12/21 DM / DM 22 BMW 520 i |
||||||||||||
|
11 DT / DT 12/21 DT / DT 22 |
BMW 520 i (2.2 ltr.) |
|||||||||||
|
BMWDD31523/DDi 32 / DD 41 / DD 42 31 DM / DM 32/41 DM / DM 42 |
||||||||||||
|
31 DT / DT 32/41 DT / DT 42 |
BMW 525 i |
|||||||||||
|
BMWDD51528/DDi 52 / DD 61 / DD 62 51 DM / DM 52/61 DM / DM 62 |
||||||||||||
|
51 DT / DT 52/61 DT / DT 62 |
BMW 530 i |
|||||||||||
|
DE 11 / DE 12 / DE 21 / DE 22 DN 11 / DN |
BMW 535 i |
|||||||||||
|
12 / DN 21 / DN 22 |
||||||||||||
|
DE 51 / DE 52 / DE 61 / DE 62 DN 51 / DN |
BMW 540 i |
|||||||||||
|
52 / DN 61 / DN 62 |
||||||||||||
|
DM 71 |
BMW 520 d |
|||||||||||
|
DL 91 / DL 92 / DL 01 / DL 02 |
BMW 525 d |
|||||||||||
|
DF 51 / DF 52 |
BMW 525 td |
|||||||||||
|
DF 71 / DF 72/81 DF / DF 82 |
BMW 525 tds |
|||||||||||
|
DL 71 / DL 72 / DL 81 / DL 82 |
BMW 530 d |
Size in inches, offset and bore in mm. How to read these figures.
Before you buy or fit