Wheel fitment and offset explained
Illustration drawn for this guide.

Technical guide

Wheel fitment and offset explained

Whether a wheel fits a car depends on a handful of numbers: bolt pattern, offset, width, centre bore and the shape of the fastener seat. Get them right and the wheel sits where it should and stays on. Get one wrong and you can have rubbing, vibration or loose wheels.

PCD
Stud count x circle diameter, e.g. 5x112
Offset
ET in mm, centreline to mounting face
Width
Measured between bead seats, in inches
Common threads
M12x1.5, M12x1.25, M14x1.5
Seat types
Conical 60 degree, radius (ball), flat

Bolt pattern (PCD)

PCD stands for pitch circle diameter. It is written as the number of studs or bolts followed by the diameter of the circle they sit on, in millimetres. 5x112 means five holes on a 112 mm circle, a pattern used across many Volkswagen, Audi and Mercedes-Benz models. 5x120 is typical of BMW, 4x100 of many older small cars, and 5x114.3 of a lot of Japanese cars.

The PCD has to match exactly. Patterns that are close, such as 5x112 and 5x114.3, cannot be forced together safely. Wobble bolts and adapters exist for small differences, but they are a compromise and should only be used with parts approved for the purpose. On multi-piece BBS wheels the centre determines the PCD, so a centre drilled for one car will not suit another without replacing it or redrilling by an expert, and redrilling is not appropriate for every design.

Measuring a five-hole pattern is awkward because no two holes sit directly opposite each other. A PCD gauge is the easiest tool. Without one, measure from the centre of one hole to the far edge of a non-adjacent hole and compare with published charts.

Offset (ET) and what it does

Offset is the distance in millimetres from the wheel's centreline to the face that bolts against the hub. The German term Einpresstiefe gives the abbreviation ET used on BBS wheels. A positive offset means the mounting face is outboard of the centreline, so the wheel sits further inside the arch. A lower or negative offset pushes the wheel outward.

Offset alone does not tell you where the rim edges end up. You need width as well. Two wheels with the same ET but different widths share the same mounting face position, yet the wider one extends further in both directions by half the difference in width.

Worked example 1: changing width and offset together

Suppose a car runs 8Jx18 ET35 and you are considering 8.5Jx18 ET30. Nominal widths convert as 8 inches = 203.2 mm and 8.5 inches = 215.9 mm.

  • For 8J ET35: half width is 101.6 mm. The outer bead seat sits 101.6 - 35 = 66.6 mm outboard of the mounting face. The inner bead seat sits 101.6 + 35 = 136.6 mm inboard.
  • For 8.5J ET30: half width is 107.95 mm. Outer: 107.95 - 30 = 77.95 mm. Inner: 107.95 + 30 = 137.95 mm.

So the new wheel comes out about 11.4 mm further at the outer edge and only about 1.4 mm further in on the inside. Inner clearance to struts and springs is almost unchanged, while the outside moves noticeably closer to the arch lip. Whether that fits depends on the car, the tyre and the suspension height.

Worked example 2: same width, lower ET

Going from 8Jx17 ET35 to 8Jx17 ET20 moves the whole wheel 15 mm outward. You gain 15 mm of inner clearance and lose 15 mm at the arch. This is the same effect as fitting a 15 mm spacer to the original wheel, though a spacer also changes the bolt length you need.

Measurements are taken at the bead seats. The outer flange of the rim, and the tyre sidewall, usually stand out a little further, so leave a margin.

Measuring offset yourself

On refurbished or rebuilt multi-piece wheels the marked ET may no longer be correct. To measure it:

  1. Lay the wheel face down and put a straightedge across the inner rim flange.
  2. Measure from the straightedge down to the mounting face. This is backspacing.
  3. Measure the overall width from flange to flange.
  4. ET = backspacing - (overall width / 2).

Example: overall flange width 230 mm and backspacing 150 mm gives 150 - 115 = 35, so ET35. Using overall width rather than bead seat width is fine for this calculation because the flanges are usually symmetric, but check visually on unusual lip profiles.

Centre bore and hub rings

The centre bore is the hole in the middle of the wheel that fits over the hub spigot. Factory wheels are normally made with a bore that matches the car exactly, so the wheel is centred by the hub. Aftermarket wheels often have a larger bore so one casting can fit many cars, and a plastic or aluminium hub ring fills the gap.

Common hub sizes include 57.1 mm (many VW Group cars), 66.6 mm (many recent Audi and Mercedes models), 72.6 mm (older BMW) and 66.1 or 67.1 mm on various Japanese makes. Always check the specific car rather than relying on a brand rule, because carmakers change sizes between generations.

Hub rings do not carry load. The clamping force of the bolts or nuts holds the wheel. What the ring does is centre the wheel accurately while you tighten it, which prevents a slight eccentric fitment that shows up as vibration at speed. If a wheel has the right bore for the hub, no ring is needed. If the bore is smaller than the hub, the wheel will not fit at all without machining, which should only be done by an expert who knows the design.

Bolts versus nuts

Cars hold wheels on in one of two ways. Many European cars, including most VW Group, BMW, Mercedes-Benz and Porsche models, use wheel bolts that screw into threaded holes in the hub. Many Japanese, American and some French cars use studs fixed in the hub, with nuts.

The threads differ too. M12x1.5 is very common on bolts and studs. M14x1.5 appears on many newer European cars. M12x1.25 is used by several Japanese makers. Never mix them up; a nut that seems to go on with effort may be cross-threading.

Thread engagement matters. As a widely used rule, a steel bolt or stud should engage for at least about as many turns as its diameter in millimetres divided by the pitch, which for M12x1.5 means roughly 6.5 to 8 full turns. When you move to a wheel with a thicker mounting pad, as many multi-piece wheels have, or add a spacer, the original bolts can be too short. Measure the depth and buy the correct length.

Seat types

The seat is the contact surface between the fastener and the wheel. It must match the shape cut into the wheel, or the fastener will only touch on a thin line and can loosen.

  • Conical or tapered seats are usually 60 degrees. They are the most common aftermarket type and widely used on BMW and Japanese cars.
  • Radius or ball seats have a spherical shape. VW and Audi factory wheels typically use radius seats, and the radius itself varies, so check before buying bolts.
  • Flat seats with a separate washer appear on some older wheels and on some Mercedes and Toyota factory designs.

A frequent mistake is fitting aftermarket BBS wheels with conical seats to a VW using the factory radius-seat bolts, or the reverse. Both look like they fit and both are wrong. Check the wheel's seat shape and use matching hardware.

Load ratings

Every road wheel has a maximum load it is designed for, usually stated per wheel in kilograms. Factory wheels are designed for the car's axle loads with a margin. Aftermarket wheels are approved to a stated load, and in markets such as Germany that load appears in the approval paperwork.

A worked check: a car with a maximum permitted axle load of 1,100 kg on the front needs front wheels rated for at least 550 kg each. Heavy saloons, estates and SUVs can exceed what a wheel designed for a small hatchback can take, even when the PCD and offset suit. Older lightweight BBS wheels made for small cars may not carry a modern heavy car safely, so confirm the rating before swapping wheels between very different vehicles.

Tightening

Tighten in a star or cross pattern, in two stages, to the carmaker's torque figure. Typical values for passenger cars fall roughly in the 100 to 140 Nm range, but use the figure for your car. Multi-piece wheels have their own assembly bolt torque, which is separate from the wheel fastener torque and should only be touched by someone with the correct figure for that design. Recheck wheel fasteners after a short drive when wheels are new or newly refinished, because paint can settle under the seat.

Frequently asked questions

What does ET35 mean?

The wheel's mounting face sits 35 mm outboard of its centreline. Lower ET pushes the wheel outward, higher ET pulls it inward.

Do I need hub rings?

You need them when the wheel's centre bore is larger than the hub. They centre the wheel during tightening but do not carry load.

Can I use my factory bolts with aftermarket BBS wheels?

Only if the seat shape and length match. Factory radius-seat bolts are wrong for conical-seat wheels, and thicker mounting pads may need longer bolts.

Is 5x112 the same as 5x114.3?

No. They are close but not interchangeable, and forcing one onto the other is unsafe.

How do I check if wheels are strong enough for my car?

Compare the wheel's load rating per wheel with half the car's maximum axle load. The wheel rating should be equal or higher.

Related

More guides